14.5. Using the IPsec Termination Rule¶

14.5.1. Referring the IPsec Termination Rule¶

Following is the procedure for referring the IPsec termination rule.

1. Click [1] on the Manage Integrated Network Appliance screen.

2. The IPsec Termination Rule tab appears.

Refer to the following table (information that can be referred with the IPsec Termination Rule tab) for contents to be displayed for each item.

* Information that can be referred with the IPsec Termination Rule tab

Item	Contents to be displayed
a	Enabling/ disabling the IPsec termination setting
b	Identification name of each IPsec termination rule
c	Local end point of each IPsec termination rule
d	Peer end point of each IPsec termination rule
e	Enabling/ disabling each IPsec termination setting
f	Status of each IPsec termination rule (healthy/unhealthy)
g	Destination of local network connected with each IPsec termination rule
h	Destination of peer network connected with each IPsec termination rule

14.5.2. Enabling/ Disabling the IPsec Termination Function¶

Following is the procedure for enabling/disabling the IPsec termination rule.

1. When enabling the IPsec termination function on the IPsec Termination Rule tab, click [1] and [2] to enable the IPsec termination function.

2. When disabling the IPsec termination function, remove the check mark on the check box [3] and then click [4] to enable the IPsec termination function.

14.5.3. Adding the IPsec Termination Rule¶

Following is the procedure for adding the IPsec termination rule.

1. Click [1] on the IPsec Termination Rule tab.

2. The Add IPsec Termination Rule screen appears. After inputting the necessary parameters, click [2].

* Refer to the following table (input rules applied on the Add IPsec Termination Rule screen) for contents to be input on each item.

* Input rules applied on the Add IPsec Termination Rule screen

	Input field	Input contents	Mandatory/ Optional	Input condition
a	Text box	This item can be used for inputting the identification name of each IPsec termination rule.	Mandatory	Half-width characters (1 to 80 characters)
b	Text box	This item can be used for inputting the description of this IPsec termination rule.	Optional	Half-width characters (1 to 80 characters)
c	Check box	This item can be used for enabling/disabling this rule.	Optional	None
d	List	This item can be used for selecting the server segment connected to the external VLAN with IPsec communication.	Mandatory	None
e	Text box	This item can be used for inputting the external VLAN connected with IPsec communication.	Mandatory	IPv4 address subnet
f	Pulldown menu	This item can be used for selecting the interface of the integrated network appliance terminating the IPsec communication.	Mandatory	None
g	Text box	This item can be used for inputting a unique ID configured for the integrated network appliance in use.	Optional	Half-width characters (1 to 80 characters)
h	Text box	This item can be used for inputting the IS specified by the IPsec terminal equipment at the external VLAN side.	Mandatory	Half-width characters (1 to 80 characters)
i	Text box	This item can be used for inputting the fixed IP used for IPsec communication, which is allocated to the IPsec termination equipment at the external VLAN.	Mandatory	IPv4 address (decimal notation with dots)
j	Pulldown menu	This item can be used for selecting the encryption protocol used for IPsec communication.	Mandatory	None
k	Text box	This item can be used for inputting the common key used for authentication.	Mandatory	Half-width characters (32 to 128 characters) Including at least one upper case letter, lower case letter and number
l	Text box	This item can be used for inputting the common key used for authentication again for confirmation.	Mandatory	The same character string as that input in k
m	Text box	This item can be used for setting the maximum value of one frame, which is transmitted and received with IPsec communication.	Mandatory	Half-width digits in the range from 1200 to 1500